PA 6 G OIL

PA – Polyamide

PA 6 G OIL

PA 6 G OIL is a cast polyamide that contains oil as a lubricant. Because of its oil content, the material’s coefficient of friction is up to 50% lower and its wear‑resistance about five times greater than that of standard polyamides. This polyamide is best suited to applications in which the material is subjected to continuous wear. We deliver PA 6 G OIL as plastic sheets and rods and as hollow rods.

Add to comparison Remove from comparison Compare products
Physical properties
  Value Unit Test method
Specific gravity 1.14 g/cm3 DIN EN ISO 1183
Average molecular mass N/A
Water absorption, 24/96 h (23 °C) 0.2/0.4 % DIN EN ISO 62
Weather-resistance moderate
Combustibility HB UL 94 DIN EN ISO 527-2
Food safety no
Mechanical properties
  Value Unit Test method
Modulus of elasticity 3100 MPa DIN EN ISO 527-2
Tensile strength 70 MPa DIN EN ISO 527-2
Elongation at break 4 % DIN EN ISO 527-2
Tensile strength at break 50 % DIN EN ISO 527-2
Flexural modulus 2900 MPa DIN EN ISO 178
Flexural strength 95 MPa DIN EN ISO 178
Compressive modulus 2700 MPa EN ISO 604
Compressive strength, 1%/2% 21/37 MPa EN ISO 604
Impact strength (Charpy) does not break kJ/m2 DIN EN ISO 179-1eU
Notch impact strength (Charpy) 5 kJ/m2 DIN EN ISO 179-1eA
Notch impact strength (Izod) – kJ/m2 DIN EN ISO 180/2A
Toughness (ball pressure) 150 MPa ISO 2039-1
Toughness (Shore D) N/A
Wear-resistance N/A
Coefficient of friction (against steel) N/A
Thermal properties
  Value Unit Test method
Glass-transition temperature 42 °C DIN 53765
Melting point 216 °C DIN 53765
Operating temperature (instantaneous) +170 °C
Operating temperature (continuous) 100 °C
Operating temperature (minimum) N/A
Thermal expansion coefficient, 23–60 °C 13 10-5 K-1 DIN EN ISO 11359-1;2
Thermal expansion coefficient, 23–100 °C 13 10-5 K-1 DIN EN ISO 11359-1;2
Specific heat capacity 1.7 J/(g×K) ISO 22007-4:2008
Thermal conductivity 0.37 W/(m×K) ISO 22007-4:2008
Electrical properties
  Value Unit Test method
Surface resistivity 1014 Ω DIN IEC 60093
Resistivity 1014 Ω×cm DIN IEC 60093
Dielectric strength 21 kV/mm DIN EN 60243-1
CTI value 600 V DIN EN 60112
Optical properties
  Value Unit Test method
Light transmittance N/A
Refractive index N/A
Optical errors N/A
Abrasion-resistance, 100 rotations with 500 g N/A

Additional downloads

Delivery selection plastic sheets, plastic rods, hollow bars
Specific gravity 1.14 g/cm3
Service temperature N/A … 100 °C
Price category €€ (€8–25/kg)

Special properties

  • self-lubrication
  • excellent wear-resistance
  • low coefficient of friction
  • good elongation-related and impact-resistance properties
  • good dimensional accuracy
  • excellent sliding characteristics

Applications

slide bearings, slide and chain applications, conveyor tracker rollers, feed screws, slide plates

Standard colours

yellow, black, natural

Special colours

green, red

Premade pieces

enquire

Commonly known brands

Ertalon® LFX, GEHR PA 6 G-Oil®, LiNNOTAMGLiDE, OILON®, Oilamid®, PA 6C OFN, SUSTAMID® 6 G OL, TECAST® L, ZELLAMID® 1100 Oil